A typeface for FDM printing

Text made for the nozzle, not for ink.

Bead is a font made for 3D printers. Regular fonts were drawn for ink, so the slicer has to patch every letter with tiny fills and stop-start moves. Every line in Bead is exactly two nozzle passes wide, so names, serial numbers and labels go down as clean walls.

2extrusion lines in every stroke
0.80 mmstroke width at a 0.42 mm line
5.6 mmsmallest cap height
78characters: capitals, lowercase, digits and punctuation

Bead vs. Roboto Bold in the slicer

PRINTAGO 0158 at a 5.6 mm cap height, sliced in OrcaSlicer 2.3.0 with the stock Bambu Lab A1 0.20 mm profile. One tag in Bead, one in Roboto Bold.

Outer wall Inner wall Gap fill Top surface Solid infill
Bead, raised: each letter is a single blue wall loop
Bead, raised0 mm gap fill
Roboto Bold, raised: every stroke has an orange gap-fill line down the middle
Roboto Bold, raisedgap fill in every stroke

Cut-in text

Bead's counters are four lines across, so they fill with two walls from each side. Letters sit six lines apart, so the walls of neighboring letters never merge.

Bead, cut in, layer under the surface: walls and infill, almost no gap fill
Bead, under the surface2.7 mm gap fill
Roboto Bold, cut in, layer under the surface: orange gap fill between letters
Roboto Bold, under the surface39 mm gap fill
Bead, cut in, top layer
Bead, top layer1.4 mm gap fill
Roboto Bold, cut in, top layer
Roboto Bold, top layer28 mm gap fill

Compared with twelve fonts

The same tag, the same size and the same profile, once per font. Gap fill is the plastic the slicer adds to patch what its walls could not cover. Less is better.

Raised text, top layer, as OrcaSlicer laid it
Bead, raised text, top layer, arachne walls
Bead 0 fill scraps
Roboto Regular, raised text, top layer, arachne walls
Roboto Regular 0 fill scraps
Overpass Regular, raised text, top layer, arachne walls
Overpass Regular 0 fill scraps
Osifont, raised text, top layer, arachne walls
Osifont 0 fill scraps
Bebas Neue, raised text, top layer, arachne walls
Bebas Neue 7 fill scraps
Oswald SemiBold, raised text, top layer, arachne walls
Oswald SemiBold 8 fill scraps
Montserrat Bold, raised text, top layer, arachne walls
Montserrat Bold 95 fill scraps
Overpass Bold, raised text, top layer, arachne walls
Overpass Bold 8 fill scraps
Roboto Bold, raised text, top layer, arachne walls
Roboto Bold 11 fill scraps
Inter Bold, raised text, top layer, arachne walls
Inter Bold 21 fill scraps
Open Sans Bold, raised text, top layer, arachne walls
Open Sans Bold 48 fill scraps
Liberation Sans Bold, raised text, top layer, arachne walls
Liberation Sans Bold 31 fill scraps
Printable (FontStruct), raised text, top layer, arachne walls
Printable (FontStruct) 7 fill scraps
Raised textGap fill, mm, three text layers
Bead0 0 mm of gap fill in 0 pieces · 60 separate paths
Roboto Regular0 0 mm of gap fill in 0 pieces · 57 separate paths
Overpass Regular0 0 mm of gap fill in 0 pieces · 57 separate paths
Osifont0 0 mm of gap fill in 0 pieces · 57 separate paths
Bebas Neue171.7 171.7 mm of gap fill in 156 pieces · 216 separate paths
Oswald SemiBold289.7 289.7 mm of gap fill in 442 pieces · 509 separate paths
Montserrat Bold379.4 379.4 mm of gap fill in 620 pieces · 716 separate paths
Overpass Bold396.3 396.3 mm of gap fill in 346 pieces · 414 separate paths
Roboto Bold403.1 403.1 mm of gap fill in 633 pieces · 702 separate paths
Inter Bold409.4 409.4 mm of gap fill in 688 pieces · 754 separate paths
Open Sans Bold416.9 416.9 mm of gap fill in 765 pieces · 829 separate paths
Liberation Sans Bold433.4 433.4 mm of gap fill in 659 pieces · 722 separate paths
Printable (FontStruct)491.4 491.4 mm of gap fill in 1005 pieces · 1041 separate paths
Cut-in textGap fill, mm, top layer
Bead1.4 1.4 mm on the top layer · 2.7 mm on the layer below
Overpass Regular10.3 10.3 mm on the top layer · 29.5 mm on the layer below
Open Sans Bold20.5 20.5 mm on the top layer · 31.6 mm on the layer below
Roboto Regular21.7 21.7 mm on the top layer · 30.2 mm on the layer below
Osifont23 23 mm on the top layer · 37.9 mm on the layer below
Overpass Bold24.2 24.2 mm on the top layer · 40.5 mm on the layer below
Printable (FontStruct)25.3 25.3 mm on the top layer · 35.3 mm on the layer below
Inter Bold26.5 26.5 mm on the top layer · 33.7 mm on the layer below
Montserrat Bold27 27 mm on the top layer · 29.8 mm on the layer below
Liberation Sans Bold27 27 mm on the top layer · 39.4 mm on the layer below
Roboto Bold28.2 28.2 mm on the top layer · 38.7 mm on the layer below
Bebas Neue33.4 33.4 mm on the top layer · 44.6 mm on the layer below
Oswald SemiBold41.3 41.3 mm on the top layer · 42.9 mm on the layer below
Raised textCut-in text
FontStroke width, mmSeparate pathsGap fill, mmFill scraps with ArachneGap fill, top layer, mmGap fill, layer below, mmText width, mmPlastic laid, % of letter area
Bead0.7960001.42.75794
Roboto Regular0.66570021.730.256.6110
Overpass Regular0.66570010.329.558109
Osifont0.5357002337.948.2131
Bebas Neue0.81216171.7733.444.637.193
Oswald SemiBold0.96509289.7841.342.942.794
Montserrat Bold1.25716379.4952729.864.597
Overpass Bold0.98414396.3824.240.559.594
Roboto Bold1.00702403.11128.238.757.995
Inter Bold1.01754409.42126.533.759.795
Open Sans Bold1.04829416.94820.531.659.795
Liberation Sans Bold0.98722433.4312739.461.796
Printable (FontStruct)0.901041491.4725.335.359.595

Measured from the G-code OrcaSlicer 2.3.0 wrote, classic walls unless marked. Roboto Regular, Overpass Regular and Osifont also slice raised text with no gap fill at this size: their strokes are thinner than two lines, so the two walls overlap and they lay 9 to 31% more plastic than the letter's area.

Fine details

How Bead is drawn

Bead is a center line with a fixed stroke around it. The outlines are generated for one nozzle setup, so every dimension is a whole number of lines.

0 6 8 9 B cut in, layer under the surface: every counter is filled by inner walls

Counters that fill with walls

The inside of a 6, 8 or B is four lines across. Two walls from each side meet in the middle and there is nothing left for the slicer to patch. This is the layer under cut-in text.

Two lines, every stroke

A stroke is 0.80 mm at a 0.42 mm line width and 0.2 mm layers. One wall out, one wall back.

An open cut for the bed face

Printing cut-in text face down? The open cut joins each counter to the plastic around it with a two-line bridge, so no counter prints as a separate island on the first layer.

Look-alikes kept apart

Slashed zero. Flagged 1 against a barred I. An angular 5 against a round S.

Fewer sharp inside corners

A is an arch. M and W are squared. A raised N turns through two hairpins, so the walls cover its joints. Acute corners are where plastic piles up.

The letter grows, the stroke stays

Bead Medium and Large are taller letters. The stroke is still two lines.

Sizing

Each Bead file is drawn for one text height, and that height depends on your nozzle. Pick the row for your nozzle, pick a size, and set the text to the height shown. Every stroke then comes out two lines wide.

Bead SmallBead MediumBead Large
NozzleLine widthStrokeCapital heightFont sizeCapital heightFont sizeCapital heightFont size
0.2 mm0.220.422.94.23.85.45.27.5
0.4 mm0.420.805.68.07.210.210.014.2
0.6 mm0.621.188.211.810.615.114.721.0
0.8 mm0.821.5510.915.514.020.019.427.8

All values in mm. Capital height is how tall a capital letter stands. Font size is the number Bambu Studio, OrcaSlicer and Printago Studio ask for. Line width is the stock Bambu Lab value for each nozzle, and the smallest size was sliced on all four. Layer height barely matters: the 0.4 mm files sliced just as cleanly from 0.12 to 0.28 mm layers.

A different line widthmm
SizeCapital heightFont size
Bead Small5.68.0
Bead Medium7.210.2
Bead Large10.014.2
Which file
Bead Small, Medium, LargeRaised text
Bead Small Cut, Medium Cut, Large CutText cut into a surface
Bead Small Open, Medium Open, Large OpenCut-in text printed face down on the bed

Small is the smallest text that still prints as two lines. Medium and Large are taller letters with the same stroke. At twice the height in the table, every stroke is four lines wide, which also slices cleanly.

Checked against other fonts on a 0.6 mm nozzle

Font, 8.2 mm capitalsRaised, gap fillCut-in, top layerCut-in, layer below
Bead, generated for 0.60.62.45.8
Bead, the 0.4 files scaled up0.63.17.5
Overpass Regular012.439.6
Roboto Bold407.74052.4

Gap fill in mm, sliced in OrcaSlicer 2.3.0 with the stock Bambu Lab A1 0.6 nozzle, 0.30 mm Standard profile.

Character set

0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz. , : ; ! ? ' " - _ ( ) / + = #
78 charactersCapitals, lowercase and digits16 punctuation marksThree sizes: Small, Medium and LargeRaised, cut-in and open cuts

Try it

Maya, Lot #42
Bead Small. On a 0.4 mm nozzle, set capitals 5.6 mm tall (font size 8.0 mm) so each stroke prints as two lines.

Bead in Printago

Printago is 3D print farm software that runs production from order to finished print. Its text builder has Bead built in: set a text placeholder in Bead Small and Printago redraws it for every order, with no font to upload.

Sign up for free today

No credit card required. Connect unlimited printers and get production automation running in minutes.